The control link is the invisible line between your sticks and your drone. When it fails, the drone falls. ExpressLRS (ELRS) and TBS Crossfire are the two links most FPV pilots consider. Crossfire built its name on reliable long range. ELRS arrived later as an open-source project and now ships on most new drones and radios. The ELRS vs Crossfire debate is not about which one is "better" in general. It is about which one fits the way you fly. This guide compares them on the points that really matter in the air.
ELRS vs Crossfire at a Glance
| Criterion | ExpressLRS (ELRS) | TBS Crossfire |
|---|---|---|
| Type | Open source | Proprietary (Team BlackSheep) |
| Frequency bands | 2.4 GHz and 868/915 MHz versions | 868/915 MHz |
| Packet rate | From about 25 Hz up to 1000 Hz (2.4 GHz) | 50 Hz and 150 Hz modes |
| Latency | Very low at high packet rates | Low, but higher than fast ELRS modes |
| Penetration | 2.4 GHz weaker; 900 MHz strong | Strong on 900 MHz |
| Receiver cost | Low | Higher |
| Hardware choice | Many brands | TBS ecosystem |
| Best fit | Racing, freestyle, budget builds, most beginners | Proven long range, existing TBS setups |
Our view: ELRS is the default for most new pilots. Crossfire stays a solid choice for pilots already invested in TBS gear.
How an FPV Control Link Works
Your radio sends stick positions to a receiver on the drone many times per second. Each update is a packet. The packet rate, measured in hertz, shows how often the drone gets new commands. Two factors matter most. Latency is the delay between moving a stick and the drone reacting. Link margin is how much signal is left before the connection drops. Higher frequencies such as 2.4 GHz allow fast packet rates but pass through obstacles less well. Lower frequencies such as 868/915 MHz penetrate trees and buildings better but carry fewer packets. Every link balances these two.
Latency and Packet Rate
This is where ELRS stands out. On 2.4 GHz it can run at packet rates of 500 Hz and higher, which gives very low latency. Racers and freestyle pilots feel the difference as sharper, more connected control.
Crossfire runs at 150 Hz in its standard mode and drops to 50 Hz to gain range. For cinematic flying and long-range cruising, this is more than enough. For tight racing gates, many pilots prefer faster ELRS modes.
ELRS also lets you pick a lower packet rate when you need range. You trade some latency for link margin, so one system covers many flying styles.
Range and Penetration
Crossfire is famous for range and for holding the link behind obstacles. Its 900 MHz band passes through trees and walls better than 2.4 GHz.
ELRS on 2.4 GHz still reaches several kilometres in open air with good antennas, which is far beyond what most pilots need. Behind buildings or dense forest it loses signal sooner. For that kind of flying, ELRS also offers 868/915 MHz hardware that competes directly with Crossfire on penetration.
Remember local rules: allowed power and frequencies differ by country, especially on 868 MHz in Europe and 915 MHz in the US.
Cost and Ecosystem
ELRS receivers are cheap and made by many brands. Most new radios include an ELRS module, and many BNF drones ship with ELRS receivers. That makes it easy to build a fleet without spending much.
Crossfire receivers cost more, and the hardware comes from one company. In return, you get a mature, consistent ecosystem with simple setup through TBS tools.
Setup and Configuration
ELRS Setup
ELRS uses a binding phrase. You set the same phrase on the radio and the receivers, and they connect automatically. Firmware and settings are managed through a configurator or over Wi-Fi. There are more options to learn, but also more control.
Crossfire Setup
Crossfire binding is done from the radio menu, and updates go through the TBS Agent software. Fewer settings make it straightforward for pilots who just want a link that works.
Which Link Should You Choose
- First drone or first radio: ELRS 2.4 GHz. It is cheap, fast and supported almost everywhere.
- Racing and freestyle: ELRS 2.4 GHz at a high packet rate.
- Long range in open terrain: either ELRS or Crossfire on 900 MHz.
- Flying behind trees and buildings: a 900 MHz link from either system.
- Already own TBS gear: Crossfire still works very well; there is no urgent reason to switch.
Whatever you choose, set up failsafe correctly and range-test before every new kind of flight.
Where ELRS and Crossfire Came From
Understanding where each system came from explains much of the ELRS vs Crossfire debate.
TBS Crossfire was developed by Team BlackSheep, a well-known FPV hardware company. It brought long-range, low-frequency control to the hobby at a time when most pilots flew on short-range 2.4 GHz systems. Crossfire quickly became the standard for long-range and cinematic pilots, and it built a reputation for links that simply do not drop.
ExpressLRS started as a community project. Its developers used modern LoRa radio chips and open-source firmware to build a fast, long-range link that any manufacturer could produce. Because it is open, many companies make ELRS receivers and modules, which brought prices down and pushed the technology forward quickly. Today ELRS is built into most new radios and many ready-to-fly and bind-and-fly drones.
The result is two very different philosophies. Crossfire is a closed, consistent product from one company. ELRS is an open standard with many makers, frequent updates and a large choice of hardware.
Packet Rate Modes in Practice
Both systems let you choose how often control packets are sent. The right mode depends on how and where you fly.
| System and band | Mode | Typical use |
|---|---|---|
| ELRS 2.4 GHz | 50 Hz | Maximum range in open terrain, slow flying |
| ELRS 2.4 GHz | 150 Hz | Long range with good control |
| ELRS 2.4 GHz | 250 Hz | All-round freestyle and cinematic flying |
| ELRS 2.4 GHz | 500 Hz | Freestyle and racing with very low latency |
| ELRS 2.4 GHz | 1000 Hz | Racing at short range, where every millisecond counts |
| ELRS 868/915 MHz | 25–200 Hz | Long range and flying behind obstacles |
| Crossfire 868/915 MHz | 50 Hz | Long-range cruising |
| Crossfire 868/915 MHz | 150 Hz | Standard mode for most flying |
A higher packet rate gives quicker response but less range. A lower packet rate improves sensitivity and range but adds delay. Most pilots never need the extremes. A middle setting, such as 250 Hz on ELRS 2.4 GHz, suits most freestyle and cinematic flights.
Does Latency Really Matter?
For racers flying through gates at high speed, a few milliseconds can change a line. For cinematic pilots filming smooth shots, the difference is hard to feel. Video latency and the pilot's own reaction time are often larger than the link latency. Choose your packet rate by flying style, not by the lowest number on a chart.
Telemetry Ratio
Both systems send telemetry back from the drone: battery voltage, link quality and signal strength. On ELRS you can set how often telemetry is sent. More telemetry gives more information on the radio screen; less telemetry leaves more of the link for control. For most pilots, the default setting is the right one.
Features That Make a Difference in the Air
Beyond range and latency, a few features decide how comfortable and safe each link is to use.
Dynamic Power
Both systems can raise transmitter power automatically when the signal weakens and lower it when the drone is close. This saves battery, reduces interference with other pilots and keeps power in reserve for difficult moments. Pilots report that ELRS adjusts power very quickly, which helps in sudden signal drops, for example when diving behind a building.
Model Match
Model match makes sure your radio only connects to the drone that belongs to the selected model. It prevents a dangerous mistake: flying one drone with the settings or switches meant for another. Turn it on if you fly several drones.
Configuration from the Radio
Both ELRS and Crossfire can be configured from the radio screen using small scripts. You can change packet rate, power and telemetry in the field without a computer. ELRS also offers Wi-Fi updates for modules and receivers, which makes firmware management easy once you learn it.
Redundancy Options
Some newer ELRS hardware supports a mode that sends each packet on two frequencies at once, which adds redundancy against interference. Crossfire pilots who want more redundancy usually use diversity receivers with two antennas. TBS also offers Tracer, its own 2.4 GHz system built for low latency, for pilots who want to stay within the TBS ecosystem.
Antennas and Receiver Placement
A good link depends as much on installation as on the system you choose. Many "range problems" are really antenna problems.
- Keep antennas clear. Carbon fibre blocks radio signals. Mount receiver antennas so they stick out from the frame.
- Separate antennas. Keep the receiver antenna away from the video antenna and from power wires.
- Mind the orientation. Mount antennas so they are not hidden behind the battery or the frame when the drone tilts forward in flight.
- Use diversity on larger drones. Two antennas at different angles reduce dropouts.
- Check for damage after crashes. A cut or crushed antenna can reduce range dramatically while still looking fine.
- Match the antenna to the band. A 2.4 GHz antenna will not work well on a 900 MHz receiver.
On the radio side, point the antenna so its side, not its tip, faces the drone. Small details like this add a lot of link margin.
Failsafe: The Setting That Saves Your Drone
Whichever link you choose, failsafe decides what happens when the signal is lost. In Betaflight, failsafe usually works in two stages.
Stage 1
When packets stop arriving, the flight controller holds the last commands or sets predefined values for a short moment. This covers brief glitches without the drone reacting.
Stage 2
If the signal does not return, the drone takes the action you selected: disarm and drop, try a controlled landing or, on drones with GPS, return toward home with GPS Rescue. Dropping is the safest choice near people for small drones, because a drone that tries to land on its own may drift.
Test It Every Time
With props removed, arm the drone, switch the radio off and watch what happens. Repeat this after every firmware update, receiver change or new drone. A failsafe that has never been tested is a guess, not a safety feature.
ELRS vs Crossfire by Flying Style
The best way to settle the ELRS vs Crossfire question is to start from how you fly.
Tiny Whoops and Indoor Flying
Range does not matter indoors, and weight matters a lot. ELRS 2.4 GHz receivers are tiny and often built into whoop flight controllers. This is the clear choice for small drones.
Freestyle
Freestyle pilots fly close to trees, buildings and the ground, with fast direction changes. Low latency and fast dynamic power help. ELRS 2.4 GHz at 250–500 Hz is the most common setup. Crossfire still works well for freestyle, especially for pilots who already own it.
Racing
Racers want the lowest possible latency at short range. ELRS 2.4 GHz at high packet rates is built for this. Crossfire is rarely chosen for new racing builds.
Cinematic and Cinewhoop Flying
Smooth, slow shots do not need extreme packet rates, but they need a reliable link around people, buildings and indoor spaces. Either system works. ELRS keeps receiver costs down when you run several cinewhoops; Crossfire gives a consistent link if you already use TBS gear.
Long Range and Mountain Flying
This is where the 900 MHz band shines. Both Crossfire and ELRS 868/915 MHz handle distance and terrain better than 2.4 GHz. Choose by ecosystem, receiver cost and the features you prefer.
Industrial and Professional Work
Inspection, mapping and other professional tasks need predictable behaviour above all. Whichever system you choose, standardise it across your fleet, document your settings and test failsafe on every aircraft. Consistency matters more than the brand.
| Flying style | Recommended link | Typical setting |
|---|---|---|
| Tiny whoop, indoor | ELRS 2.4 GHz | Medium to high packet rate |
| Freestyle | ELRS 2.4 GHz (or Crossfire if owned) | 250–500 Hz on ELRS |
| Racing | ELRS 2.4 GHz | 500–1000 Hz |
| Cinematic, cinewhoop | ELRS or Crossfire | Mid packet rate |
| Long range, mountains | ELRS 900 MHz or Crossfire | Lower packet rate for range |
Interference and Busy Flying Fields
At a club field or a race, many pilots fly at the same time. Radio links behave differently here than when you fly alone.
Both ELRS and Crossfire use frequency hopping, which spreads the signal across many channels and makes collisions between pilots rare. Still, a crowded 2.4 GHz band, with Wi-Fi, video links and other radios, can reduce link quality. Simple habits help:
- Use dynamic power so your transmitter does not shout louder than needed.
- Do not stand next to other pilots' radios while flying.
- Watch link quality telemetry on the radio, not just signal strength.
- Keep video and control on different bands where possible, for example analog video on 5.8 GHz and control on 2.4 GHz or 900 MHz.
In practice, both systems handle busy fields well when they are set up correctly.
Firmware Updates and Version Management
Firmware is the area where the two systems feel most different in daily use.
ELRS receives frequent updates with new features and improvements. That is a strength, but it means you must keep the transmitter and receivers on compatible versions. A simple rule helps: update the transmitter and all receivers together, and write down which version each drone runs.
Crossfire updates less often and through one official tool. There are fewer choices, which many pilots find relaxing.
Whichever system you use, never update firmware right before an important flight. Update at home, test on the bench without props, then test in the air close to you.
Switching from Crossfire to ELRS
Many pilots with Crossfire gear consider moving to ELRS for cheaper receivers and lower latency. The switch is straightforward if you plan it.
- Choose the band. Pick ELRS 2.4 GHz for racing and freestyle, or ELRS 868/915 MHz if you need penetration similar to Crossfire.
- Get a transmitter module. Many radios have ELRS built in; otherwise, use an external module in the radio's module bay.
- Replace receivers one drone at a time. Keep flying Crossfire on the other drones while you convert.
- Set a binding phrase. Use the same phrase on the module and all receivers.
- Configure Betaflight. The receiver protocol stays CRSF, the serial protocol both systems use, so the change on the flight controller is usually small.
- Range-test and test failsafe. Fly close first, then increase distance gradually.
There is no need to convert everything at once. Many pilots keep Crossfire on their long-range drones and use ELRS on everything else.
Common Link Problems and How to Fix Them
| Symptom | Likely cause | Fix |
|---|---|---|
| Receiver will not bind | Firmware version mismatch or wrong binding phrase | Update both sides to compatible versions and recheck the phrase |
| Short range | Antenna damaged, badly placed or wrong band | Replace or reposition the antenna |
| Sudden failsafes at close range | Antenna shadowed by carbon or battery | Move the antenna clear of the frame |
| Link drops behind obstacles | 2.4 GHz cannot pass through | Fly around the obstacle or use a 900 MHz link |
| Jittery control | Packet rate too low or interference | Raise packet rate or move away from other transmitters |
| Telemetry missing on radio | Telemetry disabled or ratio set too low | Enable telemetry and discover sensors on the radio |
Keep a note of the setting that fixed each problem. Link issues often repeat across drones built the same way.
Frequently Asked Questions
Can ELRS and Crossfire work together?
No. They use different radio protocols, so an ELRS transmitter cannot control a Crossfire receiver and the other way round. Both connect to the flight controller with the same CRSF serial protocol, which is why switching is easy on the drone side.
Is 900 MHz ELRS compatible with Crossfire?
No. Both work on similar frequencies, but they do not understand each other's signals.
Which link is better for long range?
Both work very well. For open terrain, either system on 900 MHz gives long, reliable range. ELRS 2.4 GHz also reaches far in open air with good antennas, but it is weaker behind obstacles.
Does a higher packet rate reduce range?
Yes. Higher packet rates reduce receiver sensitivity, so the link reaches less far. Choose the lowest rate that still feels responsive for your flying style.
Do I need a licence to use a high-power transmitter?
It depends on the country and the frequency. Many regions limit transmitter power, especially on 868 MHz in Europe, and higher power on some bands may require an amateur radio licence. Always check local rules before raising power.
Which link should a beginner choose?
ELRS 2.4 GHz. It is affordable, widely supported and works with most new radios and bind-and-fly drones.
Is Crossfire outdated?
No. Crossfire is still a reliable, proven link, and many long-range and cinematic pilots fly it every day. ELRS has become the more common choice for new setups mainly because of price, latency and wide hardware support.
Can one radio run both ELRS and Crossfire?
Yes, with the right hardware. A radio with an internal ELRS module can take an external Crossfire module in its module bay, and you choose which one to use for each model.
Learn to Configure Your Control Link
Choosing a link is easy. Configuring it correctly is what keeps a drone in the air. At Dronarium Academy, we teach pilots to set up receivers, packet rates, telemetry and failsafes on real hardware. Our courses are built on real operating experience, including flying in difficult radio conditions.
The FPV Engineering & Configuration course covers assembly, programming and setup of FPV drones, including the radio link. Pilots ready for more can take the full FPV Drone Course. Training runs in Kyiv and Lviv. See all Dronarium courses.
Conclusion
In the ELRS vs Crossfire choice, ELRS wins for most pilots: lower latency, cheaper receivers and wide support across new drones and radios. Crossfire remains a proven option for long range and for pilots already using TBS equipment. For penetration behind obstacles, choose a 900 MHz link from either system. Most important of all, learn to configure your link and failsafe properly, because a good setup matters more than the brand.